PLUMBING BASICS: A MUST FOR BATHTUB INSTALLATION

Plumbing Basics: A Must for Bathtub Installation

Plumbing Basics: A Must for Bathtub Installation

Blog Article

Click Here

This post down below about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is especially engaging. Don't miss it.


How to Install a Bathtub
Mounting a tub isn't specifically rocket science, but it does require strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately challenging job. If the old tub is readily easily accessible, the task can relocate rapidly; if you need to open up a wall to remove the old bathtub and also position the new bathtub, the task is much harder. In either situation, the job is within a residence handyman's skills, although you will need a helper to move out the old tub as well as embeded in the new one. Make certain you have actually qualified yourself for the work and are comfortable attempting it. As opposed to hiring a specialist to take control of a halfway-completed task, it is better to think about utilizing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This short article will help you set up a new tub in your restroom if you have already acquired a brand-new tub and don't need to change the plan of your previous water supply pipes.
Your devices and also product checklist ought to consist of the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Planning for the Installment


    First of all, the sustaining frame provided with the bath needs to be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to stop stress on the bath tub.
    Fit the versatile tap adapters to the bottom of the two faucets using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you use all of the provided washing machines.
    Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath must now be ready to be fitted in its last placement.

    Removing Old Taps


    If you need to change old taps with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water supply. After doing so, turn on the taps to drain any kind of water remaining in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited accessibility that is typically the situation.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old sealing compound.
    Prior to carrying on to fit the new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.

    Installing the Tub


    Making use of both wooden boards under its feet, place the tub in the needed setting. The wood boards are valuable in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four little points.
    The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the bath tub up until the level reads degree.
    To set up taps, fit all-time low of the furthest adaptable tap connector to the ideal supply pipe by making a compression sign up with; then do the very same for the various other tap.
    Switch on the supply of water as well as examine all joints and also brand-new pipework for leaks and also tighten them if essential. Fill up the bathtub and also inspect the overflow outlet as well as the normal electrical outlet for leaks.
    Finally, deal with the bath paneling as defined in the producer's user's manual. Tiling and sealing around the tub needs to wait till the bathtub has been utilized at the very least when as this will certainly resolve it right into its last position.

    Fitting New Taps


    If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a link to the existing supply pipes.
    If you need to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next, position the faucet in the installing hole in the bath/basin making certain that the washers are in location in between the tap and also the sink. Safeguard the tap in position with the producer offered backnut. Once the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet ports. The former kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.

    Tiling Around the Bathtub


    In the area where the bathroom fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split a stiff seal, creating the water to pass through the wall surface in between the bathroom and the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
    You can pick from a range of coloured sealers to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealer can crack relatively very early if you do not think about this activity prior to sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or waterproof sticky as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    A Step-by-Step Guide to Installing a Bathtub

    We had been made aware of that report on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an associate on our other site. Appreciated our piece of writing? Please share it. Help another person discover it. Bless you for your time. Visit us again soon.


    One-stop solution, phone now!

    Report this page